Its design makes it portable and easy to install in test racks. It comes with an automotive-grade MQS connector (Power and 100BASE-T1) and a standard Ethernet RJ-45 connector. It communicates with standard Ethernet through an RJ-45 connector. No customized driver is needed to interact with this MediaConverter. Thus, we ensure a trustworthy and effective tool to our customers that are looking for a cost-efficient, quick, and manageable solution for their testing requirements, with no latency and no packet loss. It is based on the reference implementation officially used by the OPEN Alliance for standardization of BroadR-Reach® into IEEE 100BASE-T1. After approval of the circuit design and phy register settings, this device, which uses the Broadcom BCM89810 PHY, became our first mass-production product in 2010. Technica Engineering manufactured and supported the first introduction of this technology to the automotive industry in 2008. This device is the product of the very first Evaluation Board ever produced for Automotive Ethernet – called BroadR-Reach®. A massive housing made of galvanized sheet steel with black powder coating, coupled with DIP switches for ease of configuration, enables the user to interact with the converter effortlessly. The device features bi-directional conversion between Standard Ethernet (100BASE-TX) and Automotive Ethernet (100BASE-T1). After approval of the circuit design and phy register settings, this device, which uses the Broadcom BCM89810 PHY, became our first mass-production product in 2010. The conversion takes place on the physical layer with the highest proven reliability. In the conversion, no packets are stored or modified. When used in the 14-Module power-redundant Powered Chassis with any combination of AC and DC power supplies, the installed modules are powered via the 5VDC chassis connector.įlexPoint unmanaged media converters are easy to use and provide dependable fiber connectivity in Enterprise and Government networks around the world.Converts IEEE 100BASE-T1 100 Mbit/s Fullduplex, 1x Unshielded Twisted Pair to Standard Fast Ethernet 100BASE-TX Fullduplex 2 x shielded or unshielded twisted pair with an RJ-45 connector. Standalone modules can also be powered by attaching an external DC power supply (18-60VDC). They can also be rack-mounted in a 5-Module shelf or in a high-density 14-Module, power-redundant Powered Chassis.įlexPoint modules installed in the 5-Module shelf or used as standalone devices can be powered by an external AC to DC power adapter, or through the 5VDC chassis connector. The LEDs report the availability of power, connection status, diagnostic or loopback modes of operation and the detection of all 1’s by the fiber and UTP ports.įlexPoint modules can be mounted utilizing optional wall-mounting hardware or with DIN-rail mounting brackets. The FlexPoint T1/E1 features descriptions of the LED indicators on the label for easy in-the-field configuration, installation and maintenance. Dry contact relay option allows a separate T1/E1 alarm circuit to be notified when a loss of power is detected. Local loopback validates connectivity to local T1/E1 lines, while remote loopback validates the entire fiber segment from one unit without having to make adjustments on both ends. Multimode fiber models support distances of up to 5km, and single-mode fiber models support distances of up to 60km.ĭiagnostic features include local loopback, remote loopback and all 1’s insertion (AIS) modes for the copper or fiber segments. The fiber port operates at 1310nm and supports SC or ST connectors. DIP-switches provide easy configuration of T1/E1 line codes and line build-out.Ī crossover switch makes it simple to connect the FlexPoint T1/E1 converter to PBXs or CSUs and eliminates the need for a crossover cable. The converter also supports AMI, B8ZS and HDB3 line codes. T1/E1 media converters operate in pairs, providing distance extension over fiber.ĭesigned as a transparent repeater, the FlexPoint T1/E1 supports standard T1, E1 and Primary Rate Interface (PRI), voice or data. The FlexPoint T1/E1 media converter provides standard T1 (1.544Mbps) or E1 (2.048Mbps) copper to fiber conversion and can be used to extend the demarcation point between service provider and networking equipment.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |